-
Jumbo Centering Head No.7
CONTOUR MARKER PRODUCT
STOCK NO.7
The Jumbo Centering Head is for pipe 1″ diameter and up. It has an 8″ Y-type head, and an adjustable dial bubble protractor . A spring loaded hardened centering pin eliminates the need for a hammer. Just make the alignment and press the trigger.
-
WIZARD WRAPS Pipe Wrap-A-Round
Pipe Wrap-A-Round
Flange Wizard Wraps are made from a non-asbestos, heat resistant material, Wizard Wrap is a high density product for heavy duty service at temperature up to 360° F
A tape measure is printed on all Wizard Wrap. This limits the need for an extra tape measure and makes mark-up easier. A “Circumference & Quartering” scale printed on every small, medium and large Wizard Wrap. This limits the need for calculations because the exact circumference, 1/4, 1/2, and 3/4 of the circumference, plus the actual pipe diameter for 2″ through 30″ pipe is printed on the outside of the Wizard Wrap. Packaged in a durable, reusable container that will hold up in your toolbox. Wizard Wraps have a nice thick edge for easier more accurate marking and to help your soapstone from slipping. They are resistant to oil, gasoline, kerosene, water, and seawater.
-
Contour Marker
The Curv-O-Mark Contour Marker is a compact, time-saving tool used to lay out pipe and structural steel joints.
The Contour Marker can be used to lay out pipe from 1-1/2 to 18 in. diameter, or structural steel members up to 18 in. The Contour Marker consists of an X-shaped frame, calibrated protractor, and a triple jointed marking arm and holder. The holder accepts a soapstone crayon (included), felt pen or pencil. The frame easily folds into a compact toolkit. It can be used right side up or upside down, depending on the direction of the line to be scribed The protractor is calibrated on both sides-one in degrees, the other in rise inches-per-foot-to service any type of measurement need. The unit comes with a Structural Adaptor designed to simplify the layout of structural joints, including l-beams, angles, channels, square tubing and similar shapes
-
Wrap A-Round
A tool for marking straight lines around pipe, or for use as a straight edge. Made out of flexible gasket material, with good resistance to heat and cold.
WRAP SIZE:
164B Medium: 100 x 1220mm (3.88in x 4ft)
176B Large: 100 x 1830mm (3.88in x 6ft)
177B XL: 125 x 2130mm (5in x 7ft)
179B XXL: 125 x 2740mm (5in x 9ft)SUITS PIPE SIZE:
164B Medium: 75-150mm (3-6 in) double-wrap, or up to 320mm (13 in) single wrap
176B Large: 75-250mm (3-10 in) double-wrap, or up to 480mm (19 in) single wrap
177B XL: 100-300mm (4-12 in) double-wrap, or up to 560mm (22 in) single wrap
179B XXL: 150-405mm (6-16 in) double-wrap, or up to 720mm (28 in) single wrap -
Radius Marker
Models are available in four sizes for scribing circles up to 80″ diameter. All are a folding type . All have sturdy friction joints to maintain rigidity and accuracy, and are made from lightweight, rustproof aluminum for long wear. A soapstone crayon is already installed in each radius marker.
-
RSK PRECISION LEVEL
The levels have ±0.2 scale all range accuracy in the main bubble
It has an insulating material which prevents heat transferring.
Levels have a bubble chamber in which the length of the bubble is manually adjustable.
MADE IN JAPAN
-
Outside Micrometer
Series 103
FEATURES
• Hammertone, baked-enamel-finished frame.
• Ratchet Stop for exact repetitive readings.
• With a standard bar except for 0-25mm modelTechnical Data
Graduation: 0.01mm, 0.001mm
Flatness: 0.6 μm for models up to 300mm/12″
1μm for models over 300mm/12″
Parallelism: (2+R/100)μm, R=max, range (mm)
Measuring faces: Carbide tipped -
Depth Micrometer SERIES 128
FEATURES
• ø4mm measuring rod.
• With measuring rod clamp.
• Carbide-tipped measuring rod model isavailable.
• With ratchet stop for constant force.Technical Data
Accuracy: ±3μm for micrometer head feed Graduation: .001” or 0.01mm
Flatness of reference face: 1.3μm for 63.5mm width base, 2μm for 101.6mm width base
Flatness of measuring rod face: 0.3μm
Parallelism between reference face and measuring rod face:
(4+L/50)μm, L=Max. measuring length (mm)
Measuring rod diameter: 4mm -
Tubular Inside Micrometers
FEATURES
• Wide range of ID measurements by combining extension rods (pipes) and
anvils with the micrometer head.
• Carbide-tipped measuring faces are available.
• Supplied in fitted plastic case except 1500 mm / 60” come in wooden case. -
Combination Square Set
FEATURES
• Measuring head are attached to the graduated steel rule (blade), allowing versatile measurements on various types of workpieces
• The measuring head come hardened or cast iron-not-hardened
• Economy sets not including a protractor head are also available -
Circumference Measuring Tape, stainless steel
For measuring the circumference and diameter at the same time with 10ths of mm .
16 mm wide steel tape with etched mm graduation and reader with vernier.
Reading of circumference on the lower edge of tape, on the upper reading of the corresponding diameter.Typ 161R-1
Circumference: 60 – 950mm, Diameter: 20 – 300mmTyp 161R-2
Circumference: 60 – 2200mm, Diameter: 20 – 700mmTyp 161R-3
Circumference: 60 – 3780mm, Diameter: 20 – 1200mmTyp 161R-4
Circumference: 60 – 4720mm, Diameter: 20 – 1500mmTyp 161R-5
Circumference: 60 – 5980mm, Diameter: 20 – 1900mmTyp 161R-6
Circumference: 60 – 7540mm, Diameter: 20 – 2400mmTyp 161R-7
Circumference: 60 – 8500mm, Diameter: 20 – 2700mmTyp 161R-8
Circumference: 60 – 9760mm, Diameter: 20 – 3100mmTyp 161R-9
Circumference: 60 – 11310mm, Diameter: 20 – 3600mm -
Feeler Gauge Bent Type
Metric feeler gauge 16 blades Stainless Steel
0.05mm to 1.00mm
Blade thickness : 0.05, 0.10, 0.15, 0.20, 0.25, 0.30, 0.35, 0.40,0.50, 0.55, 0.60, 0.70, 0.75, 0.80, 0.90, 1.00mm.
-
Plastigauge PL-E
For measurements of:0.030″ to 0.070″ (0.75mm – 1.75mm)
Contents: Each box contains 25 gauges (5 packs of 5 gauges, each gauge is 100mm or about 4 inches in length). Each pack contains measurement gauge (standard and metric) and instructions.
-
Plastigauge PL-D
For measurements of:0.020″ to 0.040″ (0.500mm – 1.00mm)
Contents: Each box contains 30 gauges (6 packs of 5 gauges, each gauge is 100mm or about 4 inches in length). Each pack contains measurement gauge (standard and metric) and instructions
-
Plastigauge PL-C
For measurements of:0.007″ to 0.020″ (0.175mm – 0.500mm)
Contents: Each box contains 100 gauges (10 packs of 10 gauges, each gauge is 100mm or about 4 inches in length). Each pack contains measurement gauge (standard and metric) and instructions.
-
Plastigauge PL-B
Plastigauge PL-B
For measurements of 0.004″ – 0.010″ (0.100mm-0.250mm)
Contents: Each box contains 100 gauges (10 packs of 10 gauges, each gauge is 100mm or about 4 inches in length). Each pack contains measurement gauge (standard and metric) and instructions
-
Plastigauge PL-A
Plasticgauge PL-A
For measurements of 0.001″ – 0.007″ (0.025mm-0.175mm)Contents: Each box contains 100 gauges (10 packs of 10 gauges, each gauge is 100mm or about 4 inches in length). Each pack contains measurement gauge (standard and metric) and instructions.
-
SEALED POWER – Plastic Gauge
Plastic Gauge
Green SPG – .001 – .003 / 0.025MM – 0.075MM
Red SPR – .002 – .006 / 0.05MM – 0.15MM
Blue SPB – .004 – .009 / 0.1MM – 0.23MM
Yellow SPY – .009″-.020″ / .23mm – .50mm
